Product Description
ESP8266 Serial to WiFi Module (ESP-01) |
With the popularity of IoT. Internet-connected devices built with Arduino shields or single-board computers like the Raspberry Pi and Beaglebone has exploded and there is a big demand for low-cost and easy-to-use WiFi modules. Thats where the ESP2866 Serial to wifi module comes into picture. |
The ESP8266 WiFi Module is a self contained SOC with integrated TCP/IP protocol stack that can give any microcontroller access to your WiFi network. The ESP8266 is capable of either hosting an application or offloading all Wi-Fi networking functions from another application processor. Each ESP8266 module comes pre-programmed with an AT command set firmware, meaning, you can simply hook this up to your Arduino device and get about as much WiFi-ability as a WiFi Shield offers (and that’s just out of the box)! The ESP8266 module is an extremely cost effective board with a huge, and ever growing, community. |
This module has a powerful enough on-board processing and storage capability that allows it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, including the front-end module, is designed to occupy minimal PCB area. The ESP8266 supports APSD for VoIP applications and Bluetooth co-existance interfaces, it contains a self-calibrated RF allowing it to work under all operating conditions, and requires no external RF parts.
|
Specifications of ESP8266-07 |
-802.11 b/g/n |
-Wi-Fi Direct (P2P), soft-AP |
-Integrated TCP/IP protocol stack |
-Integrated TR switch, balun, LNA, power amplifier and matching network |
-Integrated PLLs, regulators, DCXO and power management units |
-+19.5dBm output power in 802.11b mode |
-Power down leakage current of <10uA |
-Integrated low power 32-bit CPU could be used as application processor |
-SDIO 1.1/2.0, SPI, UART |
-STBC, 1×1 MIMO, 2×1 MIMO |
-A-MPDU & A-MSDU aggregation & 0.4ms guard interval |
-Wake up and transmit packets in < 2ms |
-Standby power consumption of < 1.0mW (DTIM3)
|
Featurs of ESP8266 ESP-12F |
· 802.11 b/g/n |
· Integrated low power 32-bit MCU |
· Integrated 10-bit ADC |
· Integrated TCP/IP protocol stack |
· Integrated TR switch, balun, LNA, power amplifier and matching network |
· Integrated PLL, regulators, and power management units |
· Supports antenna diversity |
· Wi-Fi 2.4 GHz, support WPA/WPA2 |
· Support STA/AP/STA+AP operation modes |
· Support Smart Link Function for both Android and iOS devices |
· SDIO 2.0, (H) SPI, UART, I2C, I2S, IRDA, PWM, GPIO |
· STBC, 1x1 MIMO, 2x1 MIMO |
· A-MPDU & A-MSDU aggregation and 0.4s guard interval |
· Deep sleep power <10uA, Power down leakage current < 5uA |
· Wake up and transmit packets in < 2ms |
· Standby power consumption of < 1.0mW (DTIM3) |
· +20dBm output power in 802.11b mode |
· Operating temperature range -40C ~ 125C |
· FCC, CE,IC ,ROSH and REACH certified |
ESP-12F | Common ESP8266 module version | ||
ESP-12S | Optimized from esp-12f, better antenna singal | ||
ESP-07S | Pin compatible with esp-12, IPEX connector to get greater signal | ||
ESP-01S | General DIP PTH version, less pin lead out, easy to use | ||
ESP-01M | Vertical stand on your PCBsave space and better signal | ||
Actual image of the product
Exhibition
Advantages
